Protege PRT-CTRL-SE Installation Manual

Protégé® SE Integrated System ControllerInstallaon ManualPRT-CTRL-SEPENDING

74.4 Baery Backup It is recommended that a minimum of a 4Ah baery is used as the main baery backup. From the accessory bag provided, connect the re

84.5 Baery Charge Current Seng To congure the Protégé® SE Integrated System Controller manually for the charge current, select the appropriate bae

94.7 Encrypted Module Network The Protégé® SE Integrated System Controller incorporates technically advanced encrypted RS-485 communicaons technology

10Figure 10 - EOL JumperAlways connect the Protégé® SE Integrated System Controllers NA and NB terminals to the NA and NB terminals of the expansion d

114.8 Telephone Dialer The Protégé® SE Integrated System Controller provides the ability to communicate alarms and upload/download informaon with rem

124.9 Expansion Connector The Protégé® SE Integrated System Controller has an onboard expansion connector that is used to connect serial communicaon,

134.10 Ethernet 10/100 Network Interface The communicaon between the Protégé® System and the Protégé® SE Integrated System Controller uses a 10/100 E

145.0 Door Access ControlThe Protégé® SE Integrated System Controller provides Access control funconality onboard without the requirement for addion

155.2 Mulple Wiegand Card Reader Connecon When operang the Protégé® SE Integrated System Controller in Mulple Reader mode the Protégé® SE Integrat

165.3 Door Contact Connecon The Protégé® SE Integrated System Controller allows the connecon of up to 4x contacts for monitoring and controlling acc

The specicaons and descripons of products and services contained in this manual were correct at the me of prinng. Integrated Control Technology L

175.4 Lock Output Connecon The Protégé® SE Integrated System Controller provides a connecon for 2x electric strike locks with full monitoring of the

185.5 Programming the Onboard Reader The onboard reader is programmed in exactly the same way as any other reader module is. It can be though of as if

19!The zones 9-12 and 13-16 can operate as either general purpose zone inputs or as onboard reader inputs. If used as general purpose zone inputs then

20Each zone input can use a dierent input conguraon. To program a large number of zones with a certain conguraon use the Mulple Selecon feature

216.3 Trouble Zones Each Protégé® SE Integrated System Controller can monitor up to 64 local trouble zones. Trouble zones are used to monitor the stat

227.0 Programmable OutputsThe Protégé® SE Integrated System Controller has 8x Programmable Outputs (PGM’s). The PGM’s are used to acvate sirens, bell

237.2 PGM 3/4 Outputs The PGM Outputs 3 (PGM3 CP001:03) and 4 (PGM4 CP001:04) on the Protégé® SE IntegratedSystem Controller are Open Collector Output

24Figure 25 - Conguraon Switch8.0 Hardware Conguraon 8.1 Conguraon SwitchThe Protégé® SE Integrated System Controller uses a 4 way dual in line

258.2 Defaulng a Controller The Protégé® SE Integrated System Controller can be set back to factory default using the following procedures. This will

269.0 LED Indicators The Protégé® SE Integrated System Controller includes extensive diagnosc indicators that can aid the installer in diagnosing fau

Table of Contents1.0 Welcome ...

279.7 Bell 1/Bell 2 Indicators The Bell 1/Bell 2 Indicators will show the status of the Bell Output and the over current or circuit fault condions.9.

2810.0 Mechanical DiagramThe mechanical diagram shown below outlines the essenal details needed to help ensure the correct installaon of the Protégé

2911.0 Mechanical LayoutThe mechanical layout shown below outlines the essenal details needed to help ensure the correct installaon of the Protégé®

3012.0 System CapaciesThe Protégé® SE Integrated System Controller can be proled to allow a comprehensive soluon that allows opmal performance to

3113.0 Technical SpecicaonsThe following technical specicaons are important and vital to the correct operaon of the Protégé® SE Integrated System

32?The isolated communicaons interface on the Protégé® SE Integrated SystemController uses full galvanic isolaon to prevent ground loop noise and cr

!It is important that the unit when installed is located in a dry cool locaon that is not aected by humidity. Do not locate the unit in an air condi

3413.3 Current and Validaon Example 3The example shown below refers to the specicaon’s table needed to help ensure the correct installaon of the P

3514.0 Ordering InformaonPlease use the following product codes when placing an order for the Protégé® SE Integrated System Controller. • PRT-CTRL-S

3615.0 WarrantyThe Seller warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Excep

9.0 LED Indicators ...26 9.1 Statu

Integrated Control Technology Limited11 Canaveral Drive, Albany, North Shore City 0632, Auckland, New Zealand P.O. Box 302-340, North Harbour, Aucklan

1.0 Welcome!Thank you for purchasing the Protégé® SE Integrated System Controller by Integrated Control Technology. The Protégé® System is an advanced

2.0 Protégé® System Management Suite The Protégé® System Management Suite applicaon is a Windows®™ based Integrated Access Control and Alarm Manageme

3.0 MounngThe Protégé® SE Integrated System Controller is supplied as a PCB only (Printed Circuit Board). It is recommended that the gear plate style

54.0 Connecons 4.1 Cabinet Enclosure Tamper SwitchThe cabinet enclosure tamper input signals to the monitoring staon or remote computer that an cabi

64.3 AC PowerThe Protégé® SE Integrated System Controller should be supplied by a dedicated electrical power source rated for a minimum 10Amp load and